ESA Profile 1 / R10

Composite board made from a electrostatically conductive wood chipboard, glued both sides with 0.6 mm ESA HPL type P according to EN 438. The front and rear edge are profiled with a 10 mm radius.

Field of application

• Wherever electrostatic charge needs to be prevented, the products out of our ESA systeam are essential. The conductive components in core material and coating facilitate safe and simple earthing. In workplaces, in microelectronics, laboratories and control centres.

ESA Profile 1 / R10

Core material

• Chipboard ESA
• Electrostatically conductive chipboard type P2 according to EN 312. Conductivity values according to DIN 61340-5-1.

Density (depending on thickness)

• 620 kg/m³ — 670 kg/m³ ± 10 % (EN 323)

Reaction to fire

• normally inflammable

Formaldehyde emission class

• E1 (EN 120)

Volume resistance R_D

• 1 x 10⁴– 1 x 10⁹ Ohm (EN 61340-5-1)
• measured dry, measurement voltage 100 V DC, cylindrical electrode, 20-30 °C and 20-50% rel. humidity (96 h conditioning)

Cleaning and care

• The surface can be cleaned with water and gentle cleaning agents. To remove stubborn stains, please observe the recommendations in the data sheet "Cleaning of HPL surfaces".
• The impact of water and cleaning agents should be limited to a short time period, drop quantities and standing water should be avoided. Please wipe the surface with a fluff free cloth allover and efficient dry.

Product safety

• This product is following the REACH regulation EG 1907/2006 an article. Following Article 7 it needs not to be registered.
• The material is not rated as hazardous material.

Sustainability

• Thermopal wood chipboard is a environmentally friendly wood material. We use approx. 65% wood offcuts from industry, obtained in the processing of round timber, plus industrial wood from forests in the region.
• We are supporting sustainable forestry in line with international standards. Ecological, economical and social criteria are all taken equally into account.
• We support the preservation of wood as a natural resource in the sense of a recycling economy by using approx. 35% of our source material from scrap wood of category A I and A II in accordance with the regulations of the scrap wood ordnance. By recycling these materials, we are also making an important contribution towards binding carbon and reducing hazardous carbon dioxide concentrations in the atmosphere.

Special

• Also available single postformed only.
• Available in the designs Span 140, U016, U043, U133, U154.
• Please observe the information contained in the technical data sheet "Electrostatic discharge capacity of decorative laminates (HPL)".
• No guarantee of stability can be given for uneven constructions.
• Cross-cutting is recommended on transport grounds.

Downloads

Cleaning of HPL surfaces

74.03 kB | Download

General Product Data Sheet for HPL Elements

93.51 kB | Download

Electrical properties of High Pressure Laminate (HPL)

91.55 kB | Download

ESA Profile 1 / R10

Certificates

Certificate of compliance: Proove of food harmless

1.08 MB | Download

ESA Profile 1 / R10

Processing

• Can be worked with carbide tipped tools on conventional woodworking machines.

Edging

• Thick and thin edges are suitable.

Fitting technology

• All conventional removable and non-removable fittings for solid wood and wood materials are suitable.

Installation and assembly

• Sufficient conditioning is required prior to installation and assembly. The premises themselves need to be air-conditioned according to future use.
• Please consider during construction and fitting that in ESD protection zones (EPA) the ESD work stations have to be earthed (same electrostatic potential of all elements). This can be achieved construcionally via a connection of the conductive elements of one EPA with an EPA-earth.
• Conductive materials which are fitted insulating are rechargable and therefore a risk potential.
• Please ensure that the material is processed and fitted correctly and using the best available technology.
• Please contact your ESD consultant or use corresponding technical literature for further information and concrete realisation instructions.

Storage and handling

• On all level surfaces (e.g. pallets), in dry, vented rooms.

Disposal

• We recommend material recycling or energy recovery.

Downloads

General working recommendations for edging materials made from thermosetting resins

2.17 MB | Download

Use of Decorative Laminates in wet and damp areas

1.02 MB | Download